1 gallon concentrate for making flush chemistry. For cleaning of Chiller Tank and Vibrator Rollers.

Flush N Clean is a non-caustic, organic neutral pH system cleaner flush intended to loosen and remove debris and rust from the inside of the print rollers, chiller tank and piping, maintaining proper thermal transfer for best print quality. Flush and Clean is a yellow/gold colored liquid that should be added at a rate of 1 gallon per 200 gallons of system volume. Once added, systems should circulate with cleaner present for a minimum of 2 hours and a maximum of 3 days. Upon completion, system needs to be flushed to drain until the water is completely replenished with city water and no cleaner is present.

Old Part# 8310749

Chill Guard concentrate for chill water. 1 gallon.

Chill Guard is a corrosion inhibitor designed to protect all metal components of a chiller/piping system. Chill Guard is a dark red liquid and should be added at the rate of 1 gallon of Chill Guard per 100 gallons of system water. Water should turn a pinkish/light red color when treatment is present. Over treating with Chill Guard will not hurt the system components. Minimum concentration is 1:100. System should be flushed and cleaned before initial Chill Guard treatment addition to remove any debris, dirt, construction material, etc. Tresu Flush and Clean is part# 3045520. 

Special heat exchanger compatible with fountain solution acidity.

Old part number 8310388

Compatibility:

COMBI units with filtration compatability manufactured from 2011 on.

Chill Guard concentrate for chill water. 5 gallon.

Chill Guard is a corrosion inhibitor designed to protect all metal components of a chiller/piping system. Chill Guard is a dark red liquid and should be added at the rate of 1 gallon of Chill Guard per 100 gallons of system water. Water should turn a pinkish/light red color when treatment is present. Over treating with Chill Guard will not hurt the system components. Minimum concentration is 1:100. System should be flushed and cleaned before initial Chill Guard treatment addition to remove any debris, dirt, construction material, etc. Tresu Flush and Clean is part# 3045655. 

5 gallon concentrate for making flush chemistry. For cleaning of Chiller Tank and Vibrator Rollers.

Flush N Clean is a non-caustic, organic neutral pH system cleaner flush intended to loosen and remove debris and rust from the inside of the print rollers, chiller tank and piping, maintaining proper thermal transfer for best print quality. Flush and Clean is a yellow/gold colored liquid that should be added at a rate of 1 gallon per 200 gallons of system volume. Once added, systems should circulate with cleaner present for a minimum of 2 hours and a maximum of 3 days. Upon completion, system needs to be flushed to drain until the water is completely replenished with city water and no cleaner is present.

Old Part# 8310749

Tresu Foam Eliminator - 1 quart container size

Foam Eliminator is used for eliminating any foaming on water surfaces. Dosage rate is generally a cap full to at most a full cup (8 ounces) to eliminate foam.

Old part number 8310904

Compatibility:

All models

Replacement filter for damping water on TRESU Royse Combi chiller units 2014 and newer.

Old Part# 8330206

Doser pump for fountain additives, 1-5 oz/gal. with kel res seal.

Old part number 8340161 

Compatibility:

COMBI chillers from 2008 on.

Water Treatment Glycol 5 gallons Clear (non-toxic) freeze protector for chill water.

Tresu propylene glycol is a non-toxic anti-freeze additive for use in chiller systems. Dosages vary based on location and freeze potential. Generally, a 30% mix is acceptable for most climates.

Old Part# 7328000305

Pump located in the COMBI chiller circulator which circulates fountain solution to the Press.

0.5 HP

Compatibility:

COMBI chillers

Flow switch providing low flow alarm at the evaporator plate. White plastic.

Old part number 7330751176

Compatibility:

All chillers and COMBI

Replacement filter element for the Big Blue canister chill water circuit. 30 micron cartridge, pleated. This filter is used in many TRESU chillers such as DPC, Single Zone and Combi units without the advanced 3-stage filter system.

Old part number 7332500034

Chill pump used in all Chillers and COMBI 5-12T up to 2011.

1.5 HP

Old part number 7332502466

Compatibility:

Chillers and COMBI from 5 to 12T up to 2011 manufacture.

Flow switch providing filter clogged alarm at the Chiller. Clear plastic.

Old part number 7332502653

Compatibility:

All chillers and COMBI

Pump located in COMBI and Zone units that circulates water through the roller cooling zone.

Compatibility:

COMBI chillers, Multi-zone chillers.

Replacement float switch for tank level controls. Reversible action N.C. - N.O.

Old part number 7335501209 

Compatibility:

All Chillers and COMBI